!   TITLE:  ms_demval.parm
!
!---------------------------------------------------------------------------
!       Rev -   10/30/00 D. Edwards 
!               Modified mirror_support.parm, J. Rinaldi, 07/19/2000    
!---------------------------------------------------------------------------
!
!   This is the parameter file used in the construction of the mirror
!   support, MS_DEMVAL.MAC.
!
!---------------------------------------------------------------------------
!
!
!--------------------- a.) Part Name Selection Variable --------------------
!
name='mir_supt'
arry_nam='mirsp'
!
!--------------------------- b.) Model C.S. Names --------------------------
!
ct_name='CSmirsp0'  ! cartesian
cyl_name='CSmirsp1' ! cylindrical
sph_name='CSmirsp2' ! spherical
!
!---------------------------------------------------------------------------
!
xcenter=2.336               ! X distance from -Z- to center hole
xbandj=7.125                ! X distance from -Z- to cast band journal

l2=xcenter+2.450            !----- See figure 1. -----
l1=xbandj-xcenter
l3=xcenter-1.33
l4=3.34-xcenter
h1=1.900
h2=3.800-h1
phi1=13.4
!
h3=1.19                     !----- See figure 2. -----
h4=0.750
phi2=7
                            ! Right & Left s/b when viewed from the front
dlj=2.150                   ! Diameter right (resolver end) journal
extd1=dlj
drj=1.050                   ! Diameter left (torquer end) journal
d1=0.9839
d2=0.369*2
d3=0.439*2                  !
d4=0.4990                   ! Torquer rotor journal
!
ribw=0.100                  !----- See figure 3. -----  ! 0.200
lrext=4.336
llext=4.364
!l5=lrext
!l6=3.636
!l7=l6-ribw
!l8=2.736
!l9=l8-ribw
!l10=1.836
h5=0.360
!h6=.220        ! 0.220
!h7=0.420
!phi3=5     ! 5
!rfil=.060
!
l11=.960    !0.800          !----- See figure 4. -----
l12=1.335
!h8=0.625
!h9=3.220
phi4=60
dcut=0.220
!
l13=0.654                   !----- See figure 5. -----
h10=h4-.530
!chmf1=0.225
!chmf2=0.100
phi5=30
!
!                           !----- See figure 6. -----
l15=0                       ! Dem-Val
l16=1.435
!
dhole=1.95          !was 1.025
dbore1=2.5          !was 1.754
dbore2=1.612        ! use in:    elev_reslvr_adaptor.mac
h11=0.909           !was .935
l17=0.324           !was .439
!
boredpth=h11-l17
extd2=5.366-l1
extd3=0.322
extd4=0.532
dos=2.000
!
l18=0.340
l19=.054
l20=0.336
l21=0.675
l22=5.044
extd5=9.992-l22-l2
!
l23=0.3220125
l24=0.3170125


tside=-xbandj+xcenter+l22+extd3-extd4 ! Thickness of flange by the band journal

!--- 4.4.4 Small center scallop cut
w1=1.010            ! Width between centers
r1=.500             ! Fillet radius (2 PL)
depth1=.060         ! Nominal depth of cut
pad=.1              ! Extra pad length to avoid zero/negative length lines

!--- 4.2.1 Front face bevel cut (extrusion)
xfbl=4.640          ! Distance from -Z- to left end of cut
xfbr=.040           ! Distance from -Z- to right end of cut
xorigin=-xcenter+xfbr   ! x location from hole center to right end of cut
lfb=xfbl-xfbr       ! Length of extrusion cut
w2=3.200            ! Width of cut between bevels
ab1=13              ! Bevel angles (2 PL)

!--- 4.3 Create Front two Pockets
xpl=.94             ! Left pocket location realative to -Z-
xpr=-2.00           ! Right pocket location realative to -Z-
w3=1.96             ! Pocket width
rp=.125             ! Pocket fillet radii
twall=h5            ! Wall thickness of pocket along angle phi1
hp=.420             ! Floor thickness - pocket bottom to back face
cham1=1.022         ! Chamfer length from CAD layout