/out,plt_form,out
/com, plt_form.mac
/com, plots current form
/com,     3/23/02  add cosine form

!  Plots the current form
!
arg3=1

mx_ph=0
_err=0
*vscfun,_mx_ph,max,wnd_(1,4)
*if,_mx_ph,eq,0,then
  /nerr
  *msg,error
  The winding data does not exist, or it contains an error&
  In particular, there are no phases specfied.
  _err=1
*endif

/nerr,0,1e5
*if,_err,eq,1,:end
ph_shft=360/_mx_ph



/com, check for the currform parameter
*get,_tcurf,parm,currform,type
_setcurr=0
*afun,deg
*if,_tcurf,eq,3,then
  /com, currform exists
  *if,currform,eq,'sine',then
   !  for the A phase
   _amp_th=.5
   *set,_amp_a
   *dim,_amp_a,table,2*720*_mx_ph/_amp_th
   !*vfill,_amp_a(1,0),ramp,0,.5
   *vfill,_amp_a(1,0),ramp,-720*_mx_ph,_amp_th
   *vfunc,_amp_a(1,1),sin,_amp_a(1,0)
   /title,Sine Current Input
  *elseif,currform,eq,'cos',then
   !  for the A phase
   _amp_th=.5
   *set,_amp_a
   *dim,_amp_a,table,2*720*_mx_ph/_amp_th
   !*vfill,_amp_a(1,0),ramp,0,.5
   *vfill,_amp_a(1,0),ramp,-720*_mx_ph,_amp_th
   *vfunc,_amp_a(1,1),cos,_amp_a(1,0)
   /title,Sine Current Input
  *elseif,currform,eq,'flat',then
   *set,_amp_a
   *dim,_amp_a,table,2
   _amp_a(1,0)=-1e4,1e4
   _amp_a(1,1)=1,1
   /title, Flat Current Input
  *endif
  _setcurr=1

*endif

*if,_setcurr,eq,0,then
 *get,_tampa,parm,amp_a,type
 *if,_tampa,ne,2,then
  /nerr
  /out
  *msg,error
  The arrays for the current form have not been defined&
  the currform parameter has not been specified or was not&
  a valid currform
  /out,ld_coil,out,,append
  _err=1
 *else
  /com, the amp_a array exists-use it
  *get,_damp_a,parm,amp_a,dim,x
  *set,_amp_a
  *dim,_amp_a,table,7*_damp_a
  *vlen,_damp_a
  *vfunc,_amp_a(1,0),copy,amp_a(1,0)
  _phoff=-3*360
  *voper,_amp_a(1,0),_amp_a(1,0),add,_phoff
  *vlen,_damp_a
  *vfunc,_amp_a(1,1),copy,amp_a(1,1)
  *do,_ildc1,1,6
   _nstloc=_ildc1*_damp_a+1
   _ph_shft=360*(_ildc1-3) !  /_mx_ph
   *vlen,_damp_a
   *vfunc,_amp_a(_nstloc,0),copy,amp_a(1,0)
   *vlen,_damp_a
   *voper,_amp_a(_nstloc,0),amp_a(1,0),add,_ph_shft
   *vlen,_damp_a
   *vfunc,_amp_a(_nstloc,1),copy,amp_a(1,1)
  *enddo
 *endif
*endif




   /grid,1
   /axlab,x,Electrical Angle (D)
   /axlab,y,Amp (A)
   /num,-1
   /xran
   /yran
   *vplo,_amp_a(1,0),_amp_a(1,1)
   /num,1
   /title, %mname%

:end

/out